北京静音空压机良心厂

(1)木门框安装(后塞口)：

(1) the wooden door frame installation (mouth) : 

后塞门框前要预先检查门洞口的尺寸、垂直度及木砖数量，如有问题应事先修理好。门框应用钉子固定在墙内的预埋木砖上，每边的固定点应不少于两处，其间距应不大于1.2m。在预留门洞口同时，应留出门框走头的缺口，在门框调整就位后，封砌缺口。

After the plug frame should be inspection door in advance before the mouth of the cave, the number of dimensions, verticality and wooden brick should be repaired in advance if you have any questions. Frame applied embedded within the nail in the wall brick wood, the fixed point of each side should be not less than two, the spacing should be not more than 1.2 m. In the reserve door mouth at the same time, should be set aside frame head gap, after frame adjustment in place, sealing build by laying bricks or stones. 

(2)木门扇安装要点：

(2) wooden door installation points: 

安装前检查门扇的型号、规格、质量是否合乎要求，如发现问题，应事先修好或更换。

Before the installation check whether the door leaf type, specification, quality is required, such as found that the problem should be repaired or replaced in advance. 

安装前先量好门框的高低、宽窄尺寸，然后在相应的窗边上画出高低宽窄的线，双扇门要打迭(自由门除外)，先在中间缝处画出中线，再画出边线，并保证梃宽一致，上下冒头也要画线刨直。画好高低、宽窄线后，用粗刨刨支线外部分，再用细刨刨到光滑平直，使其合乎设计尺寸要求。

Before installing well frame height and width size, then draw the high and low around the edge of the corresponding window width of the line, double doors to lap (excluding free door), to draw a line in the middle joints, then draw a line, and ensure the Ting width is consistent, also draw a line to plane straight to stir up and down. Drew a good height, width, with a rough plane plane feeder outside part, with a smooth plane plane to smooth and straight, size make it accord with design requirements. 

将扇放入框中试装合格后，按扇高的1/8～1/10，在框上按合页大小画线，并剔出合页槽，槽深一定要与合页厚度相适应，槽底要平。门扇安装的留缝宽度应符合有关标准的规定。

Fan to be included in the box, after test and qualified according to the high 1/8 ~ 1/10, and draw a line on the box hinge according to size, and removing the hinge groove, groove depth must be adapted to the thickness of the hinge, the bottom of the channel to be flat. Doors installed seam width should comply with the provisions of the relevant standards. 

(3)木门小五金安装要点：

(3) wooden door hardware installation points: 

有木节处或已填实的木节处，均不得安装小五金。安装合页、插销、L 铁等小五金时，先用锤将木螺钉打入1/3，然后用螺丝刀将木螺钉拧紧、拧平，不得歪扭、倾斜，严禁打入全部。

There are wooden section or already filled knag, shall install the hardware. Install the hardware such as hinge, bolt, L iron, use hammer first wood screw scored a third, then wood screw, screw with a screwdriver, may not be contorted, tilt, and it is strictly prohibited in all of them. 

使用硬木时，应先钻入2/3 的深度的孔，孔径为木螺钉直径的0.9 倍，然后再将木螺钉于孔中拧入。合页距门上、下端宜取立梃高度的1/10，并避开上、下冒头，安装后应开关灵活。

When using hardwoods, should be greater in two-thirds of the depth of the hole, aperture is 0.9 times the diameter of the wood screw, and then will be turned into the wood screw in the hole. Hinges on the door, the bottom YiQu made Ting 1/10 of the height, and avoid the upper and bottom rail, after installation should switch is quick. 

门拉手位于门高度中点以下，门拉手距地面以0.9～1.05m 为宜，门拉手应里外一致。门锁不宜安装在中冒头与立梃的结合处，防伤榫。门锁位置一般宜高出地面90～95cm。

Door handle below the gate height midpoint, door handle is 0.9 ~ 1.05 m from ground, door shake handshandle should be consistent within and without. Door lock shoulds not be installed in the middle rail and vertical Ting junction, prevent injury tenon. Door lock position general appropriate is 90 ~ 95 cm above the ground.