| 铝合金门，木门尺寸！值得你拥有，知识一生用 |
| 添加时间：2017/8/30 14:16:14 浏览次数： |
| 【一】正常门 [1] normal door 1. 门扇高 = 洞口高-50/外形高-40；门扇宽=洞口宽-80/外形宽-65； 1. Door fan height = hole height - 50 / contour height - 40; Door fan width = hole width - 80 / exterior width - 65; （洞口与外形之差即安装缝隙，也就是发泡胶尺寸，高有1公分，套板按4公分算（现在正常的套板厚3.6公分），所以高减5公分，宽减4*2=8公分。（即门洞变外形高减1公分，宽减1.5公分） (the mouth of the cave and shape is the difference between the installation gap, which is plastic foam size, have 1 cm high, boards calculate by 4 cm (now normal set of thickness of 3.6 cm), so subtract 5 cm high, width 4 * 2 = 8 cm. (that is, the door hole is reduced by 1 centimeter, and the width is reduced by 1.5 cm.) （外形减40即冒头的厚度，外形减65即竖板的厚度。） (the shape minus 40 is the thickness of the head and the thickness of the vertical plate is reduced by 65.) 竖板高 =（外形高-28/门扇高+12）*墙厚=2； Vertical plate height = (shape height - 28 / door fan height + 12) * wall thickness = 2; （门扇加12公分即上缝隙4公分，下缝隙8公分） (the door fan plus 12 cm is 4 cm in slit, 8 cm in the lower seam) 顶盖宽=（外形宽-78/门扇宽-13）*墙厚=1 Top cover width = (shape wide - 78 / door fan wide - 13) * wall thickness = 1 （即凸台尺寸） (the size of the raised platform) 2. 新工艺套板（实木新工艺和模压新工艺都一样）2公分的实芯多层板 2. The new process cover board (both the new technology of solid wood and the new process of mould pressing) are 2-centimeter solid core multilayer board 门套套板高=（洞口高-20）*墙厚=2； Door sleeve height = (hole height - 20) * wall thickness = 2; 顶盖不变*墙厚=1； Wall thickness = 1; 窗套套板高=（洞口高-20）*墙厚=2； Window set plate height = (hole height - 20) * wall thickness = 2; 顶盖不变*墙厚=1块 Top cover invariant * wall thickness = 1 block ★若为四方窗套 If it's a square window 四方窗套套板高=（洞口高-40）*墙厚=2，上下顶盖不变*墙厚=2 High = (hole height - 40) * wall thickness = 2, top and bottom cover unchanged * wall thickness = 2 如果有特殊情况，则依照客户要求的套板厚度计算。 If there is a special case, the thickness of the plate shall be calculated according to the requirements of the customer. 3.木地板（也就是吊脚）：门扇高=未铺木地板时门扇高-木地板，宽度不变。套板高宽不受木地板影响。 3. Wooden floor (also be the condole foot) : door fan height = unspread wood floor time door fan height - wooden floor, width remains unchanged. The plate height is not affected by the wood floor. 4.直墙（门边没有墙垛）：门扇宽=正常门扇宽-35（一面）/70（双面）；门扇高度不变，顶盖随着门扇宽度的变化而变化，套板高度不变。线条的宽度不样，减的数据不一样，（7公分宽的一面减45.两面减90.线条越宽，数字减得越大） 4. Straight wall (no battlement on the door) : door fan width = normal door fan wide - 35 (side) / 70 (double side); The height of the door fan is the same, the top cover changes with the width of the door, and the plate height is not changed. The width of the line is not the same, the data of the reduction is different. (the width of 7 centimeters is reduced by 45. 上方直墙：按正常下单后高度再减35公分。 Straight wall: 35 cm after normal order. 【二】异形门 【 2 】 alien door 1.门带亮窗 1. Door with bright window 竖板=洞口高-40/外形高-30；上冒头=门扇宽-13（凸台尺寸） Vertical plate = hole height - 40 / high - 30; Upper head = door fan wide - 13 (convex size) 下冒头=上冒头+20，双面喷漆；玻璃压条=线条长度 Lower head = upper head + 20, double-sided spray paint; Glass bar = line length 门扇高=客户要求高度，门扇宽和正常门一样（门扇宽=洞口宽-80/外形宽-65）。 Door fan height = customer request height, door wide and normal door (door fan width = hole width - 80 / contour - 65). 2.对开门 2. To open the door （1）不挫口 (1) not lower the mouth 门扇宽=[（洞口宽-90/外形宽-75）÷2]，门扇高和正常门一样。 Door fan width = [(hole width - 90 / exterior width - 75)], door fan height is the same as normal door. 冒头=（洞口宽-90/外形宽-75）*墙厚=1竖板高度和正常门一样。 The head = (hole width - 90 / exterior width - 75) * wall thickness = 1 vertical plate height and normal door. （2）挫口1公分 (2) 1 cm down 门扇宽=[（洞口宽-90/外形宽-75）+20]÷2，门扇高和正常门一样。 Door fan width = [(hole width - 90 / exterior width - 75) + 20] 2, door fan height is the same as normal door. 冒头=（洞口宽-90/外形宽-75）*墙厚=1，竖板高度和正常门一样。 The head = (hole width - 90 / exterior width - 75) * wall thickness = 1, vertical plate height and normal door. 注：和客户沟通对开门的采口方向 Note: communicate with the customer about the opening of the gate ①人在外，右外开； When he is out, he opens the door; ②人在外，右内开； If you are outside, open right. ③人在外，左外开； The person is outside, outside left; ④人在外，左内开。 People are outside, left inside. 3.子母门 3. The lash door 小门门扇宽={（洞口宽-90/外形宽-75）+20} *0.3 Door door wide = {(hole width - 90 / exterior width - 75) + 20} * 0.3 大门门扇宽={（洞口宽-90/外形宽-75）+20）*0.7，门扇高和正常门一样。 Gate door fan width = {(hole width - 90 / exterior width - 75) + 20) * 0.7, the door fan height is the same as normal door. 冒头=（洞口宽-90/外形宽-75）*墙厚=1，竖板高度和正常门一样。 The head = (hole width - 90 / exterior width - 75) * wall thickness = 1, vertical plate height and normal door. 4.对开门（子母门）带亮窗 4. Open the door (door) with bright Windows 上冒头=洞口宽-90/外形宽-75，下冒头=上冒头+20 Upper head = hole width - 90 / contour width - 75, lower head = upper head = 20 竖板=洞口高-40/外形高-30，小竖板=竖板-门扇高-40 Vertical plate = hole height - 40 / high - 30, small vertical board = vertical - door fan height - 40 下冒头和小竖板要双面喷漆，玻璃压条=下冒头长*4+小竖板*8 The lower head and the small vertical board should be painted with two sides, the glass pressure bar = the lower head length * 4 + small vertical plate * 8 5.推拉门（带护板） 5. Sliding door (with protection board) （单滑门）门扇高=洞口高-100/外形高-75，竖板高=门扇高 (single sliding door) door height = hole height - 100 / high - 75, vertical plate height = door fan height （双滑门）：门扇宽=【（洞口宽-90/外形宽-75）+100】÷2 (double sliding door) : door fan width = (hole width - 90 / exterior width - 75) + 100) sign 2 （三滑门）：门扇宽=【（洞口宽-90/外形宽-75）+200】÷3 (three sliding doors) : door fan width = [(hole width - 90 / exterior width - 75) + 200] （四滑门）：门扇宽=【（洞口宽-90/外形宽-75）+200】÷4 依次类推 (4 sliding door) : door fan width = 【 opening width - 90 / exterior width - 75) + 200] and so on 冒头=洞宽，冒头如图1 The head = hole width, the bold head is shown in figure 1 槽深60mm宽100mm，总厚度为100mm Groove depth 60mm width 100mm, total thickness is 100mm 6.（1）推拉门（滑门）带亮窗： 6. (1) sliding door (sliding door) with bright Windows: 竖板=洞口高-45/外形高-40，小竖板=竖板-门扇高-60； Vertical plate = hole height - 45 / contour height - 40, small vertical board = vertical - door fan height - 60; 上冒头=洞口宽（外形宽），下冒头=洞口宽-95/外形宽-75，下冒头如图1 Upper head = hole width (shape width), lower head = hole width - 95 / exterior width - 75, lower head is shown in figure 1 ★1米以上宽的亮窗中间加根框 An open window with a width of more than 1 meter （2）暗推拉门 (2) dark sliding door 门扇高=门洞高-100；门扇宽=门洞宽-35；竖板=门洞高-40*墙厚=1块，共3块竖板 Door height = door hole high - 100; Door width = door hole wide - 35; Vertical plate = door hole height - 40 * wall thickness = 1 block, total 3 vertical boards 7.折叠门：滑轨式折叠和平开式折叠 7. Folding door: sliding rail folding and peaceful open-fold folding 滑轨式折叠（针对槽深40mm） Slide rail folding (for groove depth 40mm) 门扇高=洞口高-75（冒头厚）-15（缝隙）；门扇宽=（洞口宽-90）÷2， Door height = hole height - 75 (bold head) -15 (gap); Door width = (hole width - 90) 竖板高=洞口高-65；冒头=洞口宽，如图： Vertical plate height = hole height - 65; Head = aperture width, as shown in figure: 槽深40mm宽50mm,总厚度为65mm，如果槽深≠40mm,则自行根据公式计算。 The depth 40mm width is 50mm, the total thickness is 65mm, and if the slot is not as deep as 40mm, it is calculated according to the formula. 平开式折叠 Flat folding 门扇高=洞口高-50/外形高-40；门扇宽=[[洞口宽-80/外形宽-65]-4]*扇数 Door height = hole height - 50 / contour height - 40; Door fan width = [[hole width - 80 / contour width - 65] * fan number 竖板高=（外形高-28/门扇高+12）*墙厚=2； Vertical plate height = (shape height - 28 / door fan height + 12) * wall thickness = 2; （门扇加12公分即上缝隙4公分，下缝隙8公分） (the door fan plus 12 cm is 4 cm in slit, 8 cm in the lower seam) 顶盖宽=（外形宽-78/门扇宽-13）*墙厚=1 Top cover width = (shape wide - 78 / door fan wide - 13) * wall thickness = 1 （即凸台尺寸） (the size of the raised platform) 8.外挂推拉门： 8. Sliding door: 单扇 Single fan 门扇高=洞口高-10/外形高-10；门扇宽=洞口宽 Door height = hole height - 10 / contour height - 10; Door width = width of hole 套板高=洞口宽-40，冒头=洞口宽*墙厚 Height = hole width - 40, bold = hole width * wall thickness 木方=（洞口宽+门扇宽）*60*40，异形套线如图3 Wooden square = (hole width + door fan width) * 60 * 40, profile set is shown in figure 3 异形套线长=木方长=24，宽=72，高=102 The length of the profile set is = 24, width = 72, height = 102 双扇 Double fan 门扇宽=（洞宽=100）÷2 Door width = (hole width = 100) 2 木方=（洞口宽+1扇门宽）*105*40，异形套线如图3 Wooden square = (hole width + 1 gate width) * 105 * 40, the profile set is shown in figure 3 异形套线，两头封板 Shaped sleeve, double seal 异形套线长=木方长+24，宽=105，高=102 The length of the heterotype is + 24, width = 105, high = 102 二、地弹簧门计算方式： 2. Calculation method of earth spring door: 门扇高度=外框尺寸-套板厚度-25 Door height = outer frame size - cover plate thickness - 25 门扇宽度=外框尺寸-套板厚度*2-12（说明根据门扇的扇数减的缝隙尺寸不一样） Door fan width = outer frame size - cover plate thickness * 2-12 (indicating different gap size according to door fan's fan number) 竖板=外框尺寸-套板厚度 Vertical plate = outer frame size - cover plate thickness 横板=外框尺寸 Horizontal plate = outer frame size 注意：地弹簧门门扇下方要加10公分的实木。 Note: add 10 centimeters of solid wood to the bottom of the door. 三、隐形门计算方式： Iii. Calculation method of invisible door: 注意：隐形门套板总厚度为5公分，门扇只能做实木工艺，门扇三方要采口，沟通合页是专用合页。 Note: the total thickness of invisible door covers is 5 cm, the door fan can only do the solid wood technology, the door fan is to be picked up, the communication hinges are dedicated pages. 门扇高度=外框尺寸-52（不是凸台，凸台再减-10） Door height = outer frame size - 52 (not convex, convex and minus 10) 门扇宽度=外框尺寸-88（不是凸台，凸台再减-20） Door fan width = outer frame size - 88 (not convex, convex and minus 20) 竖板=外框尺寸-20（为2公分套板） Vertical panel = outer frame size - 20 (for 2 cm) 横板=外框尺寸 Horizontal plate = outer frame size 配套板： Supporting plate: 竖板=（外框尺寸-40）门扇厚度*20 Vertical plate = (outer frame size - 40) door fan thickness * 20 横板=（外框尺寸-40）*20 Cross plate = (outer frame size - 40) * 20 配密度板： Density plate: 竖板=（外框尺寸-50）*10 Vertical plate = (outer frame size - 50) * 10 横板=（外框尺寸-80）*10 Cross plate = (outer frame size - 80) * 10 |
| 上一页 推拉门，门里门外都是景 |
| 下一页 实木门安装标准有哪些？ |
Copyright © 技术支持：遨游网络